Predictive maintenance for automotive manufacturing

An assembly line or a stamping line runs on a takt measured in seconds, and stopping one asset instantly stops everything downstream of it, from the next station to the end of the shift. Yet a robot's gearbox or a conveyor drive rarely fails without warning: well before the failure there's rising vibration, a telltale bearing noise or a drift from the normal temperature range, but on a line with dozens of identical stations, those signals are easy to miss until they show up as a bad weld or a stopped takt. Misoki lets you see that wear developing early, while there's still time to act without losing takt, during the next tooling changeover, not as an emergency stop mid-shift.

What Prism detects
Prism AIAutomotive
Typical assetsRobot servo drives, assembly-line conveyor drives, stamping presses, paint-booth pumps.
What Prism catchesConveyor misalignment and robot-mount looseness, before positioning accuracy degrades.

Diagnostics for production where the line takt cannot be broken

Automotive production is a synchronised chain of areas: stamping, welding, painting, assembly. Each runs at its own pace, matched to the areas next to it, so an unplanned stop of one conveyor or robotic manipulator quickly affects the whole line, well beyond its own area.

Prism AI continuously watches the condition of conveyor drives, paint booth pumps and the servo drives of robotic stations, recognising a developing defect at a stage when the intervention can still fit into the next process pause or tooling changeover instead of an emergency stop mid-takt. A certified vibration analyst confirms significant findings, so the maintenance team gets a specific conclusion about the asset, the cause and the urgency instead of raw data to interpret on its own.

Misoki works on any rotating asset on your site

Here is what teams monitor most often:

  • Assembly-line conveyor drives
  • Servo drives and gearboxes of robotic manipulators
  • Body-panel stamping press drives
  • Paint-booth pumps and paint circulation system pumps
  • Shop compressed-air system compressors
  • Paint-booth extraction and ventilation fans
  • Welding robot station drives
  • Hydraulic power unit pumps of press equipment
  • Overhead conveyor drives for body transport
  • Compressed-air compressors for pneumatic tools
  • Test-stand and roller-dynamometer drives

What the Prism AI assistant detects

  • Bearing wear in the servo drives of robotic manipulators
  • Imbalance and misalignment of conveyor drives in the assembly shop
  • Wear of hydraulic pumps in press equipment under cyclic loads
  • Electrical faults in drive motors (current and voltage analysis)
  • Cavitation in paint circulation pumps
  • Mechanical looseness of robot mounting on the pedestal caused by vibration loads
  • Resonance in overhead conveyor systems for body transport
  • Thermal drift in continuously running welding station drives
  • Vibration deviations in robot gearboxes that affect positioning accuracy

What Misoki solves for your team

High cost of lost line takt

Stopping one conveyor or robot stops the whole chain of operations after it. Early detection gives time to remove the cause before an emergency stop.

Robots losing positioning accuracy through hidden wear

Wear in a gearbox or servo drive gradually affects the quality of the weld or assembly, along with the asset itself. We pick up this wear before it shows in quality.

A large fleet of similar robots and drives on the line

Dozens of similar stations make manual checks of each one difficult. Prism itself points to the asset that needs attention first.

Frequent changeovers for a new model or tooling

Changes in takt and programme make a single baseline hard to keep. The system adapts to changing operating modes.

Telling normal cyclic motion from the start of a fault

Robotic equipment produces a lot of "normal" motion. Prism is trained to tell these signals apart.

Limited vibration analysis expertise on site

Not every plant has a certified analyst on staff to assess complex cases quickly. Our team takes on this role.

Integration with your existing systems

At an automotive plant, the line is already run by its own automation system (PLC/SCADA), which records takt, robot cycles and station statuses, while a separate quality system checks welded joints and coatings. Misoki does not duplicate these functions. The platform adds a layer that usually was not there: the continuous condition of the drives and servo drives themselves, matched when needed with line operating data to tell a mechanical fault from a temporary change in programme or takt.

If individual stations already have third-party vibration monitoring equipment, we connect to it directly instead of asking you to remove it. Confirmed findings can be passed to the plant's CMMS as a planned repair work order. For plants with strict requirements for protecting production data, deployment on local on-premises infrastructure is available.

How it works day to day.

The technologist doesn't check every conveyor and every robot separately before a shift, instead, they open one panel and immediately see which of the dozens of stations actually need attention, and which are running normally. When Prism flags a growing defect on a specific asset, say, the gearbox of a robot at the second welding station, the finding states right away which drive it is, the probable cause, and roughly how much time is left in reserve.

That information reaches technicians before the line is even switched over for a tooling changeover, so the repair becomes one item on the changeover work list, rather than a separate reason to stop the conveyor mid-shift.

Minimise downtime. Keep operations running.

  • Fewer unplanned line-cycle stops thanks to timely detection of worn drives and robots
  • Stable welding and assembly accuracy through monitoring gearbox and servo-drive wear before it affects quality
  • Fast identification of the specific problem station among a large number of identical stations on the line
  • Repair work scheduled within existing process pauses, without extra conveyor stops
  • One consolidated view of equipment condition across every section: from stamping to assembly
  • An accumulated wear history of the robotics and conveyor fleet to plan its modernisation

See what Prism finds on your machines.

Send us a week of data from one machine and we walk you through the diagnosis.