Predictive maintenance for water supply and wastewater

A pumping station or an aeration unit has no "off hours": water and wastewater keep coming, and an equipment stop here quickly turns from a technical problem into a question of regulatory compliance or environmental safety. Misoki lets you see wear on a pump or blower long before it fails, even when the site is far from the main control room.

What Prism detects
Prism AIWater & wastewater
Typical assetsPump stations, aerator drives, blowers, often unmanned.
What Prism catchesUnmanned stations diagnosed from the cabinet; work orders raised before a wet well overflows.

One view of sites spread across your whole service area

What sets this industry apart is the network: dozens of pumping and sewage lift stations, often far apart, that staff physically visit less than daily. Missing the start of a fault at such a site is a common situation when you rely only on scheduled visits.

Prism AI continuously monitors every connected station at once and gives a clear condition status, even for an operator with no specialist training in vibration analysis. More complex or critical findings are also checked by a certified vibration analyst (ISO CAT II/III), so the control room gets a specific conclusion instead of a mass of readings: what is happening with the pump or blower and what to do next.

Misoki works on any rotating asset on your site

Here is what teams monitor most often:

  • Lift-station and sewage transfer pumps
  • Raw-water intake and treatment-feed pumps
  • Blowers and aeration system equipment
  • Electric motors and drives of treatment process equipment
  • Plant and process air compressors
  • Mixers, flocculators and clarifier sludge-scraper drives
  • Sludge dewatering and processing equipment
  • Chemical dosing pumps
  • Filter station pumps and filter backwash system equipment
  • UV disinfection unit equipment
  • Screen and grit-removal drives

What the Prism AI assistant detects

  • Bearing wear in pumps and blowers under continuous load
  • Cavitation in lift-station pumps caused by fluctuating levels or inflow
  • Pump impeller clogging by solids in wastewater
  • Misalignment and imbalance of motor-pump and motor-blower drives
  • Electrical faults in drive motors (current and voltage analysis)
  • Abnormal acoustic signatures on aeration and blower equipment
  • Seal wear on sludge scrapers and clarifier mixers from abrasive media
  • Blower rotor imbalance caused by uneven fouling of the blades
  • Long-term wear trends across a distributed network of lift stations and treatment plant assets

What Misoki solves for your team

Equipment that is never allowed to stop

Wastewater inflow and water demand never stop. Early detection gives time for a planned intervention instead of an emergency one.

Sites spread across the territory

Lift stations sit far from each other and from the control room. Remote monitoring removes the need for daily site visits.

A small team for a large equipment fleet

There are often too few staff to physically cover every asset on a regular basis. We cover the whole connected fleet at once.

Consequences of an emergency stop reach beyond the site

An equipment failure can lead to a regulatory breach or an environmental incident. Early warning lowers that risk.

No vibration analysis specialist on staff

Not every water utility can keep such a specialist. We provide this expertise as part of the service.

Irregular physical inspections at remote stations

Infrequent visits mean a fault may be found late. Continuous monitoring closes the gap between inspections.

Integration with your existing systems

A water utility almost always already runs SCADA for process control, holds an archive of historical data and often has its own CMMS or EAM platform for maintenance requests. We do not suggest building diagnostics separately from all that. Misoki reads the process context it needs from SCADA (operating mode, flow, levels), adds its own analysis of equipment condition, and can send confirmed findings back into the same request system the operations team already uses.

Condition monitoring equipment already installed at individual stations does not need to be removed either: we connect to it directly and combine its readings with data from our own network in one consolidated picture, so old and new infrastructure work together side by side. For sites with data residency requirements, deployment on the site's own on-premises infrastructure is available.

How it works day to day.

The dispatcher sees the status of every connected lift station and every treatment plant asset on one panel, no calling the site "just in case" and no waiting for the next scheduled round just to confirm everything is fine. When Prism flags a developing fault at a remote station, the dispatcher gets specifics, not a generic alert: which pump, the probable cause, and what to check on site.

A crew heads out with a clear task instead of a preventive inspection done blind, especially valuable where the drive to a site takes hours. The rest of the network stays under continuous remote watch in the meantime, and the dispatcher learns about the next problem just as early, rather than from a complaint or a failure.

Minimise downtime. Keep operations running.

  • Continuous equipment monitoring across the entire network, including remote lift stations
  • Early warning before a fault affects treatment continuity or causes a regulatory breach
  • Fewer "just in case" site visits thanks to knowing exactly which site needs attention
  • Expert, confirmed findings that don't require an in-house vibration-analysis specialist
  • One consolidated platform for equipment condition across distributed sites
  • A long-term wear history to plan modernisation of the pump and blower fleet

See what Prism finds on your machines.

Send us a week of data from one machine and we walk you through the diagnosis.