Predictive maintenance for building services
A chiller that fails at the height of summer, or an air handling unit that stops in the middle of the working day, means more than a repair: it means tenant complaints, a disrupted indoor climate and reputational damage for the property management company. Misoki lets you see wear on a pump or compressor long before the building's residents or tenants feel it.
The same assets spread across dozens of sites, and all of them monitored at once
A property management company or facilities team is rarely responsible for a single building: the typical case is a portfolio of sites, each with its own chiller, several air handling units and heating system pumps. An in-house engineer physically cannot check the condition of equipment in every building every day, and a tenant notices the problem only when the room has already become too hot or too cold.
Prism AI continuously watches the condition of chillers, air handling units and pumps across every site in the portfolio at once and reports a developing fault long before it affects indoor comfort. A certified vibration analyst confirms significant findings, so the facilities team gets a specific conclusion, which asset, at which site and how urgently it needs attention, instead of learning about the problem from a tenant complaint.
Misoki works on any rotating asset on your site
Here is what teams monitor most often:
- Chiller compressors of air conditioning systems
- Pumps for heating, cooling and domestic hot water systems
- Air handling unit (AHU) drives
- Cooling tower fans
- Boiler system heat-transfer fluid circulation pumps
- Compressed-air system compressors for technical rooms
- Water-supply booster pump station drives
- Exhaust and smoke-extraction fans
- Elevator equipment drives (hoists, gearboxes)
- Underground car park drainage and sump pump drives
- Refrigeration equipment compressors of retail and warehouse spaces
What the Prism AI assistant detects
- Bearing wear in chiller compressors under seasonal peak loads
- Imbalance and misalignment of air handling unit drives
- Cavitation in heating and water supply pumps
- Electrical faults in drive motors (current and voltage analysis)
- Bearing wear in cooling tower fans caused by the humid environment
- Mechanical looseness of equipment mounting on plant floors and rooftops
- Resonance in pump sets in boiler rooms and pumping stations
- Thermal drift in drives running continuously to maintain the indoor climate
- Vibration deviations in lift gearboxes
What Misoki solves for your team
A portfolio of dozens of sites for a small technical team
It is physically impossible to make regular rounds of every chiller and every AHU in every building. We cover the whole portfolio remotely at once.
Problems are noticed only from a tenant complaint
By the time a room becomes uncomfortable, the fault has already developed. Early warning gives time to fix it before the first complaint.
Seasonal peak loads on equipment
Chillers and boilers run at their limits in heat or frost, exactly when downtime costs the most. We track wear before the peak season starts.
Equipment on rooftops and in hard-to-reach plant rooms
Regular physical inspection takes time and access. Remote monitoring removes that need.
No vibration analysis specialist on staff
Not every property management company can keep such a specialist. We provide this expertise as part of the service.
Scattered condition data, site by site
Information is not brought together into one picture across the portfolio. Misoki consolidates it for all buildings at once.
Integration with your existing systems
Most modern buildings already have a BMS/BAS that controls how the chillers, ventilation and boiler room operate. Misoki does not take over that role: the platform adds what a BMS usually cannot see, the actual mechanical condition of the equipment itself, beyond its operating parameters (temperature, pressure, flow). When needed, condition data can be matched with operating parameters from the BMS to tell a mechanical fault from a temporary change in load.
If individual sites in the portfolio already have third-party vibration monitoring equipment, we connect to it directly. Confirmed findings can automatically create a work order in the CMMS the property management company already uses. For sites with strict data protection requirements, deployment on local on-premises infrastructure is available.
How it works day to day.
The head of the technical team opens one panel and sees the condition of chillers, pumps and air handling units across the whole portfolio at once, without having to drive to every site in person or wait for a tenant's call about a comfort complaint. When Prism flags a developing fault at one of the sites, the finding states right away which building it is, which asset, and how urgently it needs attention.
That lets a field crew be dispatched precisely, to a specific site and a specific asset, instead of running routine preventive rounds through every building in turn, most of which turn up nothing.
Minimise downtime. Keep operations running.
- Fewer emergency failures of chillers, pumps and air handling units during peak load seasons
- Faults caught before a tenant reports them
- Coverage of the entire property portfolio without growing the technical team
- Targeted crew dispatches to a specific site and asset instead of blanket preventive rounds
- One consolidated view of equipment condition across every building at once
- A long-term wear history to plan equipment replacement across the whole portfolio
See what Prism finds on your machines.
Send us a week of data from one machine and we walk you through the diagnosis.