Predictive maintenance for power generation and grids

The energy sector has no room for surprises. A failed generator, turbine or house-load pump isn't just a repair, it's a risk of supply interruption for thousands of customers, regulatory penalties and reputational damage. Misoki lets you see the condition of critical rotating equipment in power generation and grids long before a developing fault turns into an emergency shutdown, no matter how remote or hard to reach the site is.

What Prism detects
Prism AIEnergy & utilities
Typical assetsTurbine auxiliaries, generators, cooling pumps, transformer cooling fans.
What Prism catchesEarly electrical-signature faults on critical motors, with fully isolated deployment for regulated grids.

Prism, the AI vibration diagnostician for generation and grids

Our wireless sensors mount on the critical rotating equipment of generation and grid assets and continuously stream vibration, temperature and electrical-signature data through the Gateway to the cloud platform. There, the Prism AI system automatically analyzes the signal against international vibration-diagnostics standards and recognizes signs of defects long before they become critical.

Important: Misoki isn't limited to our own sensors. We can connect to vibration sensors and monitoring systems already installed on site, including SCADA, historical databases and third-party measurement systems, and pull data directly through integrations, with no need to fully replace your existing infrastructure.

Every significant Prism finding is additionally reviewed by internationally certified vibration analysts (ISO CAT II/III), so you get not a chart but a finished conclusion: the fault description, its root cause, severity level and recommended next steps.

Misoki works on any rotating asset on your site

Here is what teams monitor most often:

  • Generators (synchronous and asynchronous)
  • Steam-turbine, gas-turbine and hydro-turbine units
  • Electric motors and drives for generation and substation equipment
  • Cooling and process-system pumps (including boiler feedwater pumps)
  • Compressors for auxiliary and house-load systems
  • Cooling-system fans, induced-draft and forced-draft fans
  • Gearboxes and mechanical drive trains
  • Exciters and other rotating electrical equipment
  • Condensate-system pump sets
  • Auxiliary hydraulic and lubrication power units
  • Rotating auxiliary equipment at substations

What the Prism AI assistant detects

  • Bearing defects on generators, turbines and large electric motors
  • Rotor and stator electrical faults (detected through current and voltage analysis)
  • Misalignment along long drive lines
  • Imbalance of rotating assemblies
  • Cavitation in cooling and boiler-feed pumps
  • Mechanical looseness and loosened fastenings
  • Abnormal acoustic signatures near rotating equipment adjacent to switchgear
  • Long-term wear trends indicating equipment approaching end of service life
  • Thermal deviations in windings, bearings and cooling systems

What Misoki solves for your team

Critical equipment with no room to stop

The asset can't be taken offline without advance planning, Misoki gives you the time to plan it.

Remote and distributed sites

Limited technical staff on site; we provide remote monitoring without the need for constant physical presence.

Equipment past its design life

Aging infrastructure runs without a reliable condition history; we build an objective wear history to support sound decisions.

Strict supply-reliability requirements

Regulatory expectations leave little room for unplanned downtime; early warning reduces that risk.

Scattered monitoring data

Information is spread across different systems and formats; Misoki consolidates it in one place, including data from existing SCADA and third-party systems.

Hard-to-justify capital decisions

Without objective long-term data it's hard to justify modernization or equipment replacement; we provide the historical data for those decisions.

Integration with your existing systems

Energy and grid sites almost always already run SCADA, DCS or a plant historian, Misoki is built to work alongside that infrastructure, not around it. We integrate directly with your existing monitoring and control systems to pull in the operational context that matters (load, speed, process parameters) and enrich our diagnostics with it, and to feed our own equipment-condition data back into your control room.

For operators of energy and critical-infrastructure sites with strict cybersecurity requirements, we support on-premises and fully isolated (air-gapped) deployments, so sensitive operational data never leaves your network.

Existing condition-monitoring equipment from other vendors can also be connected and processed rather than replaced, giving you one consolidated picture from both your legacy instruments and the new ones.

How it works day to day.

Reliability engineers get a single, remotely accessible view across every monitored site, generating units, substations and distributed assets, instead of visiting each location in person or switching between several vendor portals. When Prism AI flags a developing fault, the finding carries enough operational context (pulled from your existing systems) to make an informed call, act now, or schedule the work for the next planned outage.

Minimise downtime. Keep operations running.

  • Early warning precisely on the assets where failure risk translates directly into supply-interruption risk
  • Less reliance on fixed-schedule capital overhauls for equipment whose condition is confirmed healthy
  • Faster, more accurate fault-type identification on generating and auxiliary equipment
  • A real usage and condition history for planning modernization and capital investment
  • One consolidated picture of asset condition across distributed, remote sites

See what Prism finds on your machines.

Send us a week of data from one machine and we walk you through the diagnosis.