Predictive maintenance for food and beverage

A filling or packaging line runs at speeds where every minute of downtime costs thousands of lost units, and sanitary requirements leave little room for mounting extra equipment. Misoki lets you spot wear on an assembly before it interrupts the production cycle or spoils a batch.

What Prism detects
Prism AIFood & beverage
Typical assetsFiller drives, washdown-area motors, refrigeration compressors.
What Prism catchesHygiene zones monitored from the MCC via current signatures, no sensor on the machine needed.

Diagnostics that stay out of the way of the production cycle

In food production, downtime is rarely "just downtime": stopping a line in the middle of a filling or packing cycle often means losing raw material already loaded or an unfinished batch. At the same time, cleaning schedules (CIP), sanitary requirements and frequent changeovers between SKUs make bulky fixed monitoring systems hard to use.

The Prism AI system tells the normal process noise of high-speed equipment apart from real signs of a fault and reports the problem early enough for it to be fixed during a planned changeover or a pause between batches, instead of in the middle of an active filling run. Every significant diagnostic result is checked by a certified vibration analyst, so the process engineer receives a clear conclusion with no mass of figures to interpret on their own.

Misoki works on any rotating asset on your site

Here is what teams monitor most often:

  • Drive motors of filling, packaging and labelling lines
  • Sanitary centrifugal pumps in hygienic design
  • Positive-displacement pumps for dosing and transfer
  • Plant and process air compressors
  • Conveyor systems on production and packaging areas
  • Mixing, blending and agitation equipment
  • Cooling and drying system fans
  • Homogenisers and high-shear equipment
  • Rotary filling and canning line equipment
  • Rotating equipment in chillers and freezer rooms
  • CIP (clean-in-place) pumps and drives

What the Prism AI assistant detects

  • Bearing wear on high-speed motors of filling and packaging lines
  • Misalignment and imbalance on conveyor and rotary line drives
  • Mechanical seal wear on sanitary pumps from frequent wash cycles
  • Cavitation in transfer and dosing pumps
  • Electrical faults on drive motors (current and voltage signature analysis)
  • Homogeniser malfunctions from high-pressure valve wear
  • Thermal drift on continuously running drives and motors
  • Vibration anomalies caused by container or product imbalance on rotary lines
  • Early bearing wear signs on hygienic equipment exposed to moisture and temperature swings

What Misoki solves for your team

Almost no time to react

High-speed lines leave no room for an unplanned stop. Early warning gives you time to fix the problem before it causes a failure.

Sanitary limits on mounting equipment

Washdowns and hygiene requirements narrow the choice of sensor locations and mounting methods. Our solutions are adapted to these conditions.

Small maintenance teams covering several shifts and lines

Keeping a technician next to every assembly at all times is physically impossible. Remote monitoring closes that gap.

Risk of losing a product batch

An equipment failure mid-cycle means lost raw material as well as downtime. Early detection lowers that risk.

Telling process noise from a real fault

High-speed equipment produces a lot of "normal" vibration. Prism is trained to tell these signals apart.

Frequent changeovers between SKUs

Changing product and format makes a single baseline of readings hard to keep. The system adapts to changing operating modes.

Integration with your existing systems

We don't ask a food plant to give up systems it has spent years investing in and configuring: line control, the process-data archive and the CMMS or EAM maintenance platform keep doing their job exactly as before. Misoki joins this ecosystem as the diagnostic layer that was missing until now: we take data from the existing infrastructure wherever possible and send confirmed findings back into it, so the process engineer and the mechanic see the result in the interface they already use, without one more separate system.

The same logic applies to hardware: if third-party vibration or condition-monitoring sensors are already installed on critical lines, we don't ask you to remove them. We connect to them and combine their data with readings from our own sensor network in one consolidated picture. For plants with data-residency requirements under food-safety programs, deployment on local infrastructure (on-premises) is also available, with no data leaving the company's own network.

How it works day to day.

The technologist and the mechanic open one panel and see the condition of every monitored piece of equipment across all lines and shifts at once, with no need to walk the floor or cross-check data from several sources. When Prism flags a developing fault, the finding is specific enough that a technician can address the root cause during the next changeover or a pause between batches, rather than waiting for scheduled maintenance or reacting after the line has already stopped.

That removes the team's need to guess which vibration is normal and which is an early warning: the decision rests on a ready-made finding, confirmed by a certified specialist when needed, not on an operator's intuition.

Minimise downtime. Keep operations running.

  • Fewer unplanned stops on high-speed filling and packaging lines
  • Maintenance planned around the real condition of the equipment rather than a fixed schedule, minimising disruption to production
  • Lower risk of losing a production batch to an equipment failure mid-cycle
  • One consolidated view of equipment condition across all lines and shifts at once
  • A shift from time-based preventive maintenance to condition-based maintenance
  • Equipment condition data and confirmed findings without manual re-entry between systems

See what Prism finds on your machines.

Send us a week of data from one machine and we walk you through the diagnosis.